|Sleep tight at night knowing those little critters are gone. Using our Thermal Heater for Bed Bug Treatment, Kills Bed Bugs In an Entire Room in several hours. No toxic materials are used in the treatment process.|
Bed Bug Room Heater Treatment System Kills Bugs WithThermal Heat
The Thermal Area Treatment Heaters come in 3 sizes 208, 240 and 480 volts. These unis generate between 18,089 and 68,260 BTUs based on the voltage of your unit.
Product Info A
Product Info B
Product Info B
These bed bug heaters are designed for small to medium sized rooms. Larger rooms will require additional base units and convectors.
How To Choose The Right Bed Bug HeaterSizing formula for TAT Series heaters: 50 Watts of heat per square foot of heated space or 50W/sq ft.
Example: An 400 square foot room will require 20,000 Watts of heat to obtain 150 degrees of sustained heat to be effective. (400 sq ft x 50 Watts per square foot = 20,000 Watts of heat or 20KW of heat).
Are there other issues that impact the heater size that I need?
Ceiling height, windows, and other insulation factors should be calculated into the total size that you are trying to treat. Since this is not an exact measurement, we recommend using a slightly larger size unit versus a smaller unit.
What else do I need to do?
Seal doors, and openings in order to stop heat from leaving the room. Remove furniture cushions, put the bed mattresses on end, pull stoves and refrigerators away from the wall, open cupboards and closet doors, remove electronic devices that can be damaged by heat.
Bed bugs can be found in furniture and mattress seams, carpeting and other hard to see areas.
Killing bed bugs takes about four hours at 140-150 degrees. The system will cycle off and on to keep the room at this temperature. After four hours, the unit will turn off.
Thermal Area Treatment Heater Features:
Heavy duty industrial construction
Forward curved centrifugal blower
High Temperature ball bearing motor
Optional replaceable filter
Single point power connection
24 volt control
Heavy duty spiral finned elements constructed of stainless steel
Safety devices include airflow switch, automatic limit control and manual reset limit control for secondary protection
Disconnect switch and Unit Mounted Thermostat with range of up to 120 to 150 F.
The TAT series is sold as a system that includes the base unit, three supplemental units and the remote timer/ temperature control (supplemental units may be purchased separately if necessary)
The "TAT" series is designed to heat small and mid-sized rooms up to 150 F. which is the desired temperature to kill bed bugs and insects. It kills adult insects and will dehydrate larvae and eggs, making them unable to hatch.
Although chemical sprays only target adult insects, they can be used before utilizing the "TAT" system in order to kill the adult insects.
The system is designed to bring the temperature up to 150 F in one hour or less, if all preliminary requirements are met.
The "TAT" system may be used for water remediation, as well, in combination with adequate ventilation. Specific models for water remediation are also available.
TAT BASE UNIT:
Heavy duty stainless steel spiral fin heating elements
High temperature, ball bearing 1/3 HP - 1075 RPM blower motor
Forward curved centrifugal blower-900 CFM of air output
Safety devices include airflow switch, disconnect switch, automatic limit control and manual reset limit control for secondary protection
50 Amp unit may be linked to a 30 Amp unit to provide heating for larger spaces.
Timer/Temp controller may be used to control both units but must use the 50 Amp base unit as the master.
SUPPLEMENTAL TAT CONVECTORS
3 convectors are an integral part of each TAT system
120 Volt, 15 Amp (Standard wall plug) - 5120 BTU size
Supplied with 25' pre wired cable that connects them to the TAT base unit control section with a three pin connector
If used in front of windows or large glass doors, they will reduce heat loss and provide more even heating TIMER/TEMPERATURE CONTROL UNIT
Timer/Temp Controller is an integral part of the TAT system
24 Volt control device that controls the heat output of the TAT base unit and up to three TAT convectors for an operating range of 120 - 150 F and for a time period of 1 -10 hours after the preset temperature is reached
Supplied with a 25' pre wired cable that connects to the TAT base unit control section using a four pin connector
Mounts on Door outside the area being treated.
LED lights will indicate when treatment is complete
Models: TAT20-480-3/3BB/1T, TAT8-208-1/3BB/1T, TAT8-240-1/3BB/1T, TAT5-208-1/3BB/1T, TAT5-240-1/3BB/1T
*Product is not for personal use and should be used by professionals and exterminators only.
Note: Sealing the treated area will assist with the time it takes to reach the effective temperature. The sealing of doors, windows, outlets and switch covers may help to prevent bugs from temporarily moving to a safe area and then returning after the temperature drops to normal.