Home Automation System

Get The INSTEON Network in Your Home for Faster, More Reliable Home Automation.

INSTEON compatibility for outstanding performance Convenient lighting and appliance remote control from anywhere in the house



Install and set up in less than 10 minutes Includes everything you need.





Upgrade your home with automated lighting, appliances, security, and more by installing an INSTEON network. INSTEON is a powerful, home-control networking technology that is affordable and simple to install and use. The dual-band network quickly and reliably transmits INSTEON messages throughout the home both wirelessly (using the SignaLinc RFs) and through the home's existing wiring.



This five-piece starter kit includes everything you need to install an INSTEON network and begin enhancing your home with remote control and lighting scenes.

This starter kit includes two SigaLinc RFs, the most important part of the INSTEON network. Installing two SignaLinc RFs creates your INSTEON network, and adding additional SignaLinc RFs will improve INSTEON signal strength and network coverage throughout your home.



The ControLinc V2 tabletop controller can be set up in less than 5 minutes to control the two included LampLinc V2 Dimmers remotely using a simple "Plug and Tap" setup process. Additional LampLincs can be purchased separately to create more advanced lighting scenes. Each of the five ON/OFF buttons on the ControLinc V2 can be set up to control one lamp or every lamp in the home remotely to create dramatic lighting scenes. Additional ControLincs can be purchased separately to add remote control to other rooms. As an example, adding a ControLinc on your bedside table would allow the remote control of downstairs lamps in the middle of the night if you hear a noise.





The LampLinc V2 Dimmers are full-featured dimmers and can control any incandescent lamps up to 300 watts.



The ControLinc and LampLinc also work with legacy X10 products. The LampLinc and any of the 5 ON/OFF buttons on the ControLinc can be given an X10 address, providing a bridge between an existing X10 network and your new INSTEON network.



Specifications



Warranty: 2 years



Specifications



2430 INSTEON ControLinc Tabletop Controller Dimensions: 6.4" x 5" x 3"

X10 Addresses: Up to 5 programmable (comes unassigned); any of 256 possible



Button Modes: INSTEON only, X10 only, INSTEON and X10 together



INSTEON Scenes: 417



ALL ON/ ALL OFF Buttons: Controls all INSTEON & X10 devices programmed in channels 1-5



Bright/Dim: Controls last pressed channel (INSTEON and X10 if programmed)



Status LED: Yes (white, can be disabled)



Sounding Device: Internal beeper (can be disabled)



Mounting: Included desk stand



AC Cord: Standard 2-pin polarized



Warranty: 2 years



Specifications



2442 SignaLinc Signal Enhancer



Dimensions: 4" x 2.5" x 1.25"



Frequency (RF): 904MHz



RF Range: 150 feet, line of sight



FCC ID: SBP2442



Status LED: Yes (white)



Pass-Through Outlet: 3-pin, rated for up to 15 amps



Outlet # Pins: 3



Warranty: 2 years



Specifications



INSTEON LampLinc Lamp Dimmer



Dimensions: 4" x 2.5" x 1.25"



Maximum Wattage 300 watts



Adj. On Level Yes



Adj. Ramp Rate: Yes



INSTEON Scenes: 417



Status Response (2-Way): Yes



Load Monitor: Yes



Preset Dim: Yes



Fade On & Off: Yes



X10 Primary Address: 1 optional (comes unassigned); any of 256 possible



X10 Scenes: 255



Status LED Yes (white)



Pass-Through Outlet: Yes, rated for up to 15 amps



Outlet Pins: 3-pin



Warranty: 2 years